Infinity Speaker System TSS CENTER4000 User Manual

TSS-4000  
TOTAL SPEAKER SOLUTIONS  
TSS-CENTER4000  
Owner’s Guide  
 
Tilting the Speaker  
Wall-Mounting the TSS-CENTER4000 Using the  
If needed, the enclosed stand allows you to tilt the speaker  
across a wide range (i.e., up a maximum of 18˚ or down a  
maximum of 7˚), as shown in Figure 3.  
Included Wall Bracket  
The customer is responsible for proper selection and use of  
mounting hardware, and for correctly and safely wall-mounting  
the speakers.  
Important!  
Do not exceed the tilt range. Doing so may cause the speaker to  
fall out of its stand.  
Step One  
Remove the wall bracket cover by removing the four wall bracket  
screws on the ends as shown.  
Step Two  
Run the speaker wire behind the wall bracket and out the hole  
in the center. After deciding where to place the center speaker,  
attach the wall bracket (in a horizontal position) to the wall  
using the appropriate screws and anchors.  
Center Hole  
Figure 3.  
Wall Bracket  
Mounting Screws and Anchors  
Not Included  
Step Three  
Run the speaker wires out through the hole in the center of  
the wall bracket cover. Resecure in place with the four wall  
bracket screws, as shown.  
3
TSS-CENTER4000  
 
Step Six  
Step Four  
The wall-bracket design allows for rotation of the speakers  
at angles up to 30 degrees of center. Position the speakers  
so they face toward the primary listening position, before  
fully tightening.  
Using the included Allen wrench, remove the top and bottom  
end caps of the speaker by unscrewing the single center screw  
on bottom.  
End Cap  
End Cap  
1/4-20 x 3/4"  
Screw  
Step Five  
Connect the wires (page 5). Replace the end caps while  
capturing the wall bracket between parts A and B of the  
end cap, securing it in place.  
Wall-Mount  
End Cap B  
Wall-Mount  
End Cap A  
4
TSS-CENTER4000  
 
WIRING THE SPEAKER  
CARE OF YOUR SPEAKER SYSTEM  
After placing the speaker, you are ready to connect it to your  
system. First, turn off all audio system power. Use high-quality  
speaker wire to make the connections. Consult the owner’s  
manuals included with your amplifier or receiver for connection  
and operation procedures.  
When needed, use a soft cloth to remove any fingerprints or  
to wipe off dust. Do not use any cleaning products or polish.  
Clean the grille by gentle vacuuming.  
Surround Modes  
When using the TSS-CENTER4000 in a Dolby* Digital or DTS®  
home theater system, make sure the receiver’s/processor’s  
center channel speaker modes are set toSmall.”  
Wiring and Polarity  
The TSS-CENTER4000 speaker has gold-plated terminals that  
can accept bare wire.To ensure proper polarity, connect each  
+ terminal on the back of the amplifier or receiver to the  
respective + (red) terminal on each speaker, as shown in  
Figure 4. Connect the – (black) terminals in a similar way.  
See the owner’s manuals that were included with your  
amplifier or receiver to confirm connection procedures.  
Important!  
Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will degrade the imaging and bass  
response of the home theater system.  
After correctly placing and wiring the TSS-CENTER4000 and  
the rest of your speaker system, adjust the levels for all of the  
channels as recommended by the manufacturer of your  
receiver/processor.  
+
Figure 4.This example shows how to connect bare wires to the  
terminals. Banana plugs may also be inserted directly into the  
rear of the connector.  
Loosen the terminals.  
Insert bare ends; tighten terminals.  
5
TSS-CENTER4000  
 
SPECIFICATIONS  
TSS-CENTER4000  
Frequency Response  
120 – 20kHz ( 3dB)  
8 ohms  
Nominal Impedance  
Sensitivity  
89dB  
(2.83V @ 1m)  
Recommended Amplifier  
Power Range  
10 – 150 watts  
Crossover Frequencies  
Low Frequency Drivers  
1,000Hz, 3,800Hz; 24dB/octave  
(4) 3-1/2" (89mm) MMD®,  
magnetically shielded  
Mid Frequency Drivers  
High Frequency Driver  
(2) 3-1/2" (89mm) MMD,  
magnetically shielded  
3/4" (19mm) MMD,  
elliptical waveguide,  
magnetically shielded  
Dimensions (H x W x D)  
Weight  
4-1/8" x 23" x 4-3/8"  
(105mm x 584mm x 111mm)  
12.7 lb (5.8kg)  
Infinity continually strives to update and improve existing products, as well as create new ones.  
The specifications and construction details in this and related Infinity publications are therefore  
subject to change without notice.  
Declaration of Conformity  
We, Harman Consumer International  
2, route de Tours  
72500 Chateau-du-Loir  
France  
declare in own responsibility that the product  
described in this owner’s manual is in compliance  
with technical standards:  
EN 61000-6-3:2001  
EN 61000-6-1:2001  
Robin Marshall  
Harman Consumer International  
Chateau-du-Loir, France 10/04  
6
TSS-CENTER4000  
 
NOTES  
 
© 2004 Harman International Industries, Incorporated  
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com  
*Trademarks of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. Infinity and MMD are registered trademarks,  
and Total Solutions is a trademark, of Harman International Industries, Incorporated.  
Part No. 400-OMCNTR 10/04  
 

Intel Computer Hardware MB865 User Manual
Jensen Car Stereo System CD1211 User Manual
JL Audio Car Speaker SB GM CAM 10W3v3 User Manual
Kidde Smoke Alarm KN COSM BCA User Manual
KitchenAid Refrigerator COUNTER DEPTH SIDE BY SIDE REFRIGERATOR User Manual
KitchenAid Refrigerator W10213162A User Manual
Kodak All in One Printer KY0730485 User Manual
Kodak Scanner A 61097 User Manual
Korg Electronic Keyboard C 720 User Manual
Kramer Electronics TV Converter Box VP 505 User Manual