Jensen Car Stereo System CD1211 User Manual

CD1211  
Owner's Manual  
AM/FM/CD Receiver  
CD1211 CD RECEIVER  
MONO  
EQ  
TUNE  
/
AUX IN  
SCAN  
 
CD1211  
INSTALLATION INSTRUCTIONS  
This unit is designed for installation in cars,  
trucks and vans with an existing radio opening.  
In many cases, a special installation kit will be  
required to mount the radio to the dashboard.  
These kits are available at electronics supply  
stores and car stereo specialty shops. Always  
check the kit application before purchasing to  
make sure the kit works with your vehicle.  
Universal Installation Using  
Mounting Sleeve  
1. Remove the detachable front panel, if it is  
attached to the chassis, by pushing the  
“Release” button.  
2. Slide the mounting sleeve off of the  
chassis if it has not already been removed.  
If it is locked into position, use the removal  
keys (supplied) to disengage it. The  
removal keys are depicted on page 5.  
3. Check the dashboard opening size by  
sliding the mounting sleeve into it. If the  
opening is not large enough, carefully cut  
or file as necessary until the sleeve easily  
slides into the opening. Do not force the  
sleeve into the opening or cause it to bend  
or bow. Check that there will be sufficient  
space behind the dashboard for the radio  
chassis.  
Pre-installation  
1. Disconnect Battery  
MO  
NO  
CD  
12  
11  
CD  
EQ  
RE  
CE  
IV  
ER  
SC  
AN  
TU  
/
NE  
AU  
X
IN  
Before you begin, always disconnect the battery  
negative terminal.  
6. Follow the wiring diagram carefully and  
make certain all connections are secure  
and insulated with crimp connectors or  
electrical tape to ensure proper operation.  
7. After completing the wiring connections,  
attach the front panel and turn the unit on  
to confirm operation (vehicle ignition  
switch must be on). If the unit does not  
operate, recheck all wiring until the  
problem is corrected. Once proper  
operation is achieved, turn the ignition  
switch off and proceed with final mounting  
of the chassis.  
2. Remove Transport Screws  
4. Locate the series of bend tabs along the  
top, bottom and sides of the mounting  
sleeve. With the sleeve fully inserted into  
the dashboard opening, bend as many of  
the tabs outward as necessary to firmly  
secure the sleeve to the dashboard.  
5. Place the radio in front of the dashboard  
opening so the wiring can be brought  
through the mounting sleeve.  
M
O
N
O
C
D
1
2
1
1
C
D
EQ  
R
E
C
E
IVE  
R
SC  
AN  
TU  
/
N
E
AU  
X
IN  
8. Carefully slide the radio into the mounting  
sleeve, making sure it is right-side-up, until  
it is fully seated and the spring clips lock it  
into place.  
3
 
CD1211  
9. Attach one end of the perforated support  
strap (supplied) to the screw stud on the  
rear of the chassis using the hex nut  
provided. Fasten the other end of the  
perforated strap to a secure part of the  
dashboard, either above or below the  
radio, using the screw and hex nut  
2. Install the radio/mounting plate assembly  
to the sub-dashboard according to the  
instructions in the installation kit.  
3. Attach the support strap to the radio and  
dashboard as described in the Universal  
Installation instructions.  
Longer screws may damage components  
inside the chassis.  
4. Replace the dashboard trim panel.  
provided. Bend the strap, as necessary, to  
position it. CAUTION: The rear of the radio  
must be supported with the strap to  
prevent damage to the dashboard from  
the weight of the radio or improper  
ISO Installation  
This unit has threaded holes in the chassis side  
panels which may be used with the original  
factory mounting brackets of some vehicles to  
mount the radio to the dashboard. Please  
consult with your local car stereo shop for  
assistance on this type of installation.  
operation due to vibration.  
10. Re-attach the front panel to the chassis  
and test radio operation by referring to the  
operating instructions for the unit.  
4. Wire the new radio to the vehicle as  
outlined in the Universal Installation  
instructions.  
5. Mount the new radio assembly to the  
dashboard or center console using the  
reverse procedure of step 1.  
1. Remove the existing factory radio from the  
dashboard or center console mounting.  
Save all hardware and brackets as they  
will be used to mount the new radio.  
2. Carefully unsnap the plastic frame from  
the front of the new radio chassis. Remove  
and discard the frame.  
NOTE: For proper operation of the CD  
player, the chassis must be mounted within  
20° of horizontal. Make sure the unit is  
mounted within this limitation.  
Reconnect Battery  
3. Remove the factory mounting brackets  
and hardware from the existing radio and  
attach them to the new radio. Do not  
exceed M5 x 9 MM maximum screw size.  
When wiring is complete, reconnect the battery  
negative terminal.  
Kit Installation  
If your vehicle requires the use of an installation  
kit to mount this radio, follow the instructions  
included with the installation kit to attach the  
radio to the mounting plate supplied with the kit.  
1. Wire and test the radio as outlined in the  
Universal Installation instructions.  
4
 
CD1211  
Remove Radio  
To remove the radio after installation, remove  
the trim ring by lifting in the center and pulling it  
off from either side. Insert the removal keys  
straight back until they lock, and then pull the  
radio out. If removal keys are inserted at an  
angle, they will not lock properly to release the  
unit.  
Removal Key  
5
 
CD1211  
WIRING  
1. Power Antenna (dark blue wire) - Connect  
to power antenna or amplifier. If not used,  
tape bare end of wire.  
5
2. Accessory/Ignition (red wire) - Connect to  
existing radio wire or radio fuse.  
3. Ground (black wire) - Connect to ground  
terminal or clean, unpainted part of  
chassis.  
1 5  
4. Memory/Battery (yellow wire) - Connect to  
battery or 12 volt power source that is  
always live. The radio will not work if this  
wire is not connected.  
Dark Blue  
1
5. Antenna Connector - Connect the antenna  
plug from the existing antenna cable  
(some vehicles require an adaptor).  
6. Outputs to Amplifier (gray RCA cables) -  
Connect line out for optional external  
amplifiers. The red connector is for the  
right and the white connector is for the left.  
7. Left Front Speaker  
Black  
3
4
Yellow  
+
Gray  
6
Red  
NOTE: The amplifiers in this radio are  
only designed for use with four  
speakers. Never combine (bridge)  
outputs for use with two speakers.  
Never ground negative speaker leads  
to chassis ground. Failure to wire  
exactly as shown may cause electrical  
damage to the radio.  
2
8. Right Front Speaker  
9. Left Rear Speaker  
10. Right Rear Speaker  
White/Black (-)  
White (+)  
Gray/Black (-)  
Gray (+)  
7
Fuses  
8
When replacing a fuse, make sure the new fuse  
is the correct type and amperage. Using an  
incorrect fuse could damage the radio. The  
CD1211 uses one 15 amp fuse located below  
the wiring connector (15 amp fast blow ATO).  
Green/Black (-)  
Violet/Black (-)  
Violet (+)  
9
10  
Green (+)  
6
 
CD1211  
OPERATING INSTRUCTIONS  
clockwise or counter clockwise to adjust the  
bass from “-10” to “+10”. “00” represents a flat  
response. The bass level is shown on the  
display for five seconds or until another function  
is activated.  
Power  
Select  
Press the power button (1) or any other button  
on the face of the receiver to turn the unit on  
when the ignition switch is on. Press the power  
button again to turn the receiver off. If the radio  
was left on when the ignition was last turned off,  
the receiver will turn on automatically when the  
ignition switch is again turned on. If the receiver  
was off when the ignition was last turned off, the  
receiver must be turned on manually when  
restarting the vehicle.  
Press the AUDIO CONTROL button (4) to step  
through the menu of audio functions: volume  
(VOL), bass (BAS), treble (TRB), balance  
(BAL), fader (FAD), and volume (VOL). When  
adjusting audio functions, the unit will  
automatically exit select mode and return to the  
normal display after five seconds or when  
another function is activated.  
Treble  
Press the AUDIO CONTROL button (4) three  
times until “TRB” appears in the display. Within  
five seconds, turn the AUDIO CONTROL (3)  
clockwise or counter clockwise to adjust Treble  
from “-10” to “+10”. “00” represents a flat  
response. The treble level is shown on the  
display for five seconds or until another function  
is activated.  
Bass  
Press the AUDIO CONTROL button (4) twice  
until “BAS” appears in the display. Within five  
seconds, turn the AUDIO CONTROL (3)  
Mode  
Press MODE (2) to select a different mode of  
operation as indicated on the display panel.  
Available modes include Tuner, CD, and  
Auxiliary Input. During CD player operation,  
pressing MODE will change to the tuner mode  
without ejecting the disc. To access the  
Auxiliary Input mode, press the MODE button  
until "AUX" is indicated in the display.  
10  
6
20  
14  
CD1211 CD RECEIVER  
MONO  
Volume  
TUNE  
EQ  
/
To increase the volume, turn the AUDIO  
CONTROL (3) clockwise. To decrease the  
volume, rotate the AUDIO CONTROL counter  
clockwise. When volume is adjusted, the  
volume level is shown on the display panel as a  
number ranging from “00” (lowest) to “100”  
(highest).  
AUX IN  
SCAN  
9
13  
1
4
3
2
19  
5
8
7
 
CD1211  
Balance  
X-BASS (BAND)  
Equalizer Selector (EQ)  
Press the AUDIO CONTROL button (4) four  
times until “BAL” appears in the display. Within  
five seconds, turn the AUDIO CONTROL (3)  
clockwise (or counter clockwise) to adjust  
Balance between the right and left speakers  
from “BAL 10R” (full right) to “BAL 10L” (full  
left). “BAL L=R” represents an equal balance  
level between the right and left speakers. The  
balance position is shown on the display for five  
seconds or until another function is activated.  
Press and hold the BAND button (5) for two  
seconds to activate the X-BASS feature. When  
listening to music at low volume levels, this  
feature will boost the bass and treble ranges to  
compensate for the characteristics of human  
hearing. When activated, “X-BAS” appears on  
the display. Press BAND again for two seconds  
to deactivate this feature.  
The equalizer function applies preset sound  
effects to the unit’s audio output signal. Press  
EQ (20) to activate one of the following  
operating modes: FLAT, CLASSICS, POP M,  
ROCK M or DSP OFF. When the equalizer  
function is activated, the most recently selected  
bass/treble levels are ignored. If the bass and/  
or treble levels are adjusted while the equalizer  
function is active, the equalizer function will  
revert to FLAT. When the equalizer function is  
not active, the unit will return to the most  
recently selected bass and treble levels.  
Audio Mute (MUTE)  
Press  
(6) to mute the audio volume. “MUTE”  
Fader  
flashes on the display. Restore volume to the  
previous setting by pressing the mute button  
again, adjusting the AUDIO CONTROL, or by  
pressing any other button on the unit.  
Press the AUDIO CONTROL (4) five times until  
“FAD” appears in the display. Within five  
seconds, turn the AUDIO CONTROL (3)  
clockwise or counter clockwise to adjust  
balance between the front and rear speakers  
from “FAD 10R” (full rear) to “FAD 10F” (full  
front). “FAD F=R” represents an equal balance  
level between the front and rear speakers. The  
fader position is shown on the display for five  
seconds or until another function is activated.  
Liquid Crystal Display (LCD)  
The liquid crystal display (LCD) panel (8)  
displays the frequency, time and activated  
functions of the unit, including an audio level  
indicator, which appears as a bar graph  
depicting the audio signal. In addition, the  
display contains a receive signal indicator that  
depicts the relative strength of the incoming  
broadcast frequency.  
Beep Tone  
The beep tone feature allows the selection of  
an audible beep tone to be heard each time a  
button is pressed on the face of the radio. To  
access the Beep Tone menu, press and hold  
the AUDIO CONTROL (4). Turn the AUDIO  
CONTROL to select from the following Beep  
Tone options:  
VOL  
NOTE: After being subjected to cold  
VOL  
temperatures, LCD panels may take longer  
to respond and visibility of the numbers on  
the LCD may decrease slightly. The LCD  
display will return to normal when the  
temperature increases to a normal range.  
BEEP ALL: Beep is heard any time a  
button is pressed (function activated).  
FAD  
BAS  
BEEP 2ND: Beep is heard only when a  
secondary function is activated (press and  
hold).  
BAL  
TRB  
BEEP OFF: Beep is not heard.  
8
 
CD1211  
that it is correctly engaged, then lightly press  
the left side of the panel until the mechanism  
locks it into place.  
Display (D)  
Front Panel Release  
When the unit is off, the LCD displays the time  
of day. When the unit is on, the LCD  
automatically shows the tuner or CD display,  
depending on which mode of operation is  
currently activated.  
The front panel release button (10) releases the  
mechanism that holds the front panel to the  
chassis.  
Reset Button  
Detaching the Front Panel  
The reset button (11) is located on the front of  
the chassis and can only be accessed with the  
front panel removed. The reset circuitry  
To detach the front panel, first press the front  
panel release button (10) to release the left side  
of the panel. Next, grasp the released side and  
pull it off the chassis. After removing the front  
panel, store it in the supplied carrying case to  
protect it from dirt and damage.  
Display Clock  
protects the microprocessor circuitry. Since  
resetting the unit will erase the time and preset  
memories, it should only be activated upon  
initial installation after all wiring is complete, or  
if there is a malfunction of any of the switches  
on the unit. In these circumstances, pressing  
the reset button will clear the system and return  
the unit to normal operation.  
During tuner or CD operation, press D (9) to  
display the time of day. After five seconds, the  
display reverts to tuner or CD display.  
Set Clock  
1. To set the clock, turn the radio on in tuner  
mode (or any other mode).  
2. Press D. The time appears on the display.  
3. Press and hold D until the time display  
begins flashing.  
REMOVE FRONT PANEL  
4. While the display is flashing, press the Up  
Tuning button (14) to adjust hours and the  
“A” (AM) or “P” (PM) indication. Press the  
Down Tuning button (13) to adjust  
minutes.  
1
M
O
N
O
CD1211  
CD  
RECEIVER  
E
Q
S
RESET  
C
A
N
T
U
N
E
/
A
U
X
IN  
5. After five seconds, the time will set and the  
display will return to tuner or CD display.  
12  
11  
2
Auxiliary Input  
Theft Deterrent LED  
Re-attaching the Front Panel  
Use the Aux In connector (19) to connect a  
portable media device for playback through the  
vehicle sound system.  
A light-emitting diode (LED) (12) is located on  
the chassis behind the front panel and will flash  
when the panel is removed. The flashing light  
serves as a visual warning to the would-be thief  
that the unit has been disabled by removal of  
the front panel.  
To re-attach the front panel, make sure the  
electrical terminals on the back of the panel are  
free of dust and dirt, as debris could cause  
intermittent operation or other malfunctions.  
Position the right side of the panel in place so  
9
 
CD1211  
TUNER OPERATION  
AM/FM Band Selector (BAND)  
Scan Tuning (SCAN)  
Preset Stations  
Press BAND (5) during radio play to switch  
between three FM bands and one AM band.  
“F1”, “F2”, “F3” or “AM” will appear in the  
display to indicate the band currently selected.  
Press SCAN (15) to scan upwards through all  
the strong channels in the current band. The  
unit will pause and play each station for five  
seconds, and the station frequency will flash in  
the display during this time. Press SCAN again  
to stop scanning and listen to the current  
station.  
Up to six stations on each band can be stored  
as presets and can then be instantly recalled by  
pressing the associated preset button on the  
front panel (16) or remote control. To store a  
station, turn the radio on and select the desired  
band and station. Press and hold the desired  
preset button (numbered one through six on the  
face of the radio or remote control) for more  
than two seconds. When stored, the preset  
number will appear in the display. The station is  
now stored and can be recalled at any time by  
pressing the corresponding preset button.  
Tuning  
Automatic Tuning  
Press the Up Tuning (14) button to tune upward  
in frequency and the Down Tuning (13) button  
to tune downward in frequency. The unit will  
automatically stop at the next strong station. If  
the Local mode is active, the radio will seek the  
next strong local station when either button is  
pressed.  
NOTE: The Scan function does not work  
correctly in “MANUAL” mode.  
Manual Tuning  
14  
18 20  
Press the Up Tuning (14) or Down Tuning (13)  
button for more than two seconds to select  
manual tuning mode. “MANUAL” will appear in  
the display. Press the Up or Down Tuning  
buttons to move radio frequency up or down  
two digits at a time. Press and hold the Up or  
Down Tuning buttons to quickly advance to a  
certain frequency. Release when the desired  
frequency is reached. If tuning is not adjusted  
within five seconds of entering manual tuning  
mode, the radio will revert to automatic tuning  
and “AUTO” will appear in the display.  
CD1211 CD RECEIVER  
MONO  
EQ  
TUNE  
/
AUX IN  
SCAN  
5
15  
16  
13  
17  
10  
 
CD1211  
Repeat for the remaining five presets on the  
current band and for all presets on the other  
three bands.  
Mono/Stereo Selector (MONO)  
Press MONO (18) during FM radio operation to  
select stereo reception of the broadcast signal.  
Under normal reception, the unit should be left  
in the stereo mode as indicated by the “ST”  
designation and the associated signal strength  
indicator that appear on the display panel when  
tuned to an FM stereo signal. If the signal is too  
noisy for comfortable listening, press MONO to  
switch to mono reception. The “ST” indication  
will disappear. Press MONO again to return to  
stereo mode.  
Automatically Store / Preset  
Scan (AS/PS)  
Automatically Store  
Select six strong stations and store them in the  
current band using the Automatic Store feature.  
To enable this feature, press and hold AS/PS  
(17) for more than two seconds. The radio will  
automatically scan the band in use and enter  
strong stations into the preset memory  
positions for that band. After entering the  
stations into memory, the unit will automatically  
stop at each station for five seconds so each  
can be heard. When using the Automatically  
Store feature, the new stations replace any  
stations already stored in preset memory for the  
selected band.  
Local / Distance Selector  
This feature is used to designate the strength of  
the signals at which the radio will stop during  
automatic tuning. Distant, or “Dx” is the default  
setting, allowing the radio to stop at a broader  
range of signals. To set the unit to select only  
strong local stations during automatic tuning,  
press the LOC button on the remote control.  
“LOCAL” appears in the display.  
Preset Scan  
Press AS/PS (17) to scan the six preset  
stations in the AM band or all FM bands . The  
unit will stop at each station for five seconds  
before continuing to the next preset station, and  
the preset number will flash on the display  
during the preset scan. Press AS/PS again to  
stop scanning and listen to the current station.  
11  
 
CD1211  
CD PLAYER OPERATION  
During either function, the elapsed time will  
appear on the display. Release the button to  
resume CD play.  
Insert CD  
Disc Scan (SCN)  
With the label surface facing up, gently insert  
the disc into the CD slot (21) until the soft-  
loading mechanism engages and pulls the disc  
in. Disc play begins, “CDP PLAY” will appear in  
the display, and the CD icon will become  
animated. The center of the disc icon (7)  
illuminates and becomes animated and the  
track number and elapsed time appear in the  
display.  
During disc play, press SCN (24) to play the  
first 10 seconds of each track on the disc. “S--  
SCN” will appear in the display. When the  
desired track is reached, press SCN again to  
end the scan function and play the selected  
track. “S--SCN” will disappear from the display.  
The scan function will also be canceled when  
activating the repeat or shuffle functions.  
Play/Pause  
Press the play/pause button (23) to suspend  
disc play. “S--PAUSE” will appear in the display,  
and the center of the disc icon (7) will stop  
rotating. Press the play/pause button again to  
resume disc play. The “S--PAUSE” indication  
will disappear from the display, and play will  
resume from the pausing point.  
NOTE: The unit is designed for play of  
standard 5” (12 cm.) compact discs only. Do  
not attempt to use 3” (8 cm.) CD singles in  
this unit, either with or without an adaptor,  
as damage to the player and/or the disc may  
occur. Such damage will not be covered by  
the warranty on this product.  
14  
21  
27  
7
Track Select  
Track select features are used to quickly  
access the beginning of a particular track when  
a disc is in play. Press the Up Tuning button  
(14) to move forward or the Down Tuning  
button (13) to move backward on the disc to  
locate the desired track. Track numbers will  
appear in the display as they are accessed.  
CD1211 CD RECEIVER  
MONO  
EQ  
TUNE  
/
AUX IN  
SCAN  
Press and hold the Up or Down Tuning buttons  
23  
24  
25  
26  
13  
to fast forward or fast reverse through a disc.  
12  
 
CD1211  
Disc Repeat (RPT)  
CD Player Error Codes  
Press RPT (25) during disc play to continuously  
repeat the selected track. “S--RPT” will appear  
in the display. Press RPT again to stop  
repeating. “S--RPT” will disappear from the  
display, and regular play will resume. The  
repeat function will also be canceled when  
activating the scan or shuffle functions.  
If a problem should develop while operating the  
CD player, an error code (ER-1, ER-2, etc.)  
may appear on the display panel. This can  
indicate a number of problems with the unit,  
including a mechanical error or an error in the  
microprocessor control of the player. If an error  
code should appear, try ejecting and reloading  
the disc into the player. While the disc is out of  
the unit, make sure it is clean and undamaged,  
and then load it correctly. If this does not solve  
the problem, pressing the reset button (11) may  
help, but will erase the time and preset memory.  
If the suggested measures do not solve the  
problem, contact an approved warranty station  
near you for further assistance.  
Disc Shuffle (RDM)  
Press RDM (26) during disc play to play all  
tracks on a CD in random, shuffled order. “S--  
SHF” will appear in the display. Press RDM  
again to stop random play. “S-SHF” will  
disappear from the display and regular play will  
resume. The shuffle function will also be  
canceled when activating the scan or repeat  
functions.  
Disc Eject  
Press the eject button (27) to stop CD play and  
eject the disc. The unit will change to tuner or  
AUX operation, depending on which mode was  
in operation prior to disc play. If the disc is not  
removed from the unit within 15 seconds, the  
disc will be reloaded to prevent accidental  
damage. Disc play can be resumed by pressing  
MODE (2) to choose the CD player function.  
13  
 
CD1211  
REMOTE CONTROL  
The remote control will allow you to control the  
basic functions of the CD1211.  
The remote control sensor is located on the left  
side of the front panel to the right of the MONO  
button (18).  
S
AMS = AS/PS  
PEQ = EQ  
VOL  
VOL  
MOD = MODE  
LOC = Local/Distant  
BND = BAND  
SCN = Scan, AM, FM  
MUT =  
D
U
LOUD  
TR. UP  
TR. DN  
BND  
SCN  
MOD  
PEQ  
DISP  
LOC AMS  
MO = MONO  
DISP = Clock / Frequency  
MO  
MUT  
SCN  
2
RPT  
3
PAU  
1
5
4
6
SHUF  
DN  
UP  
14  
 
CD1211  
CARE AND MAINTENANCE  
cloth. Wipe in a straight motion from the  
inside to the outside of the disc.  
2. Never use chemicals such as record  
sprays or household cleaners to clean  
CDs, as they can irreparably damage the  
disc’s surface.  
3. Discs should be kept in their storage  
cases when not in use.  
4. Do not expose discs to direct sunlight,  
high temperatures or high humidity for  
long periods.  
CD Player  
Compact Discs  
CD-R / CD-RW  
The following guidelines will help you extend  
the life of your CD player:  
Depending on media type and method of  
"recording / burning", some CD-R/RWs may be  
incompatible with this unit. After "recording /  
burning" the session must be closed. Please  
refer to your software's recommended  
procedures for closing a disc / session. Review  
your recording software to familiarize yourself  
with the correct "recording / burning"  
1. When cleaning the vehicle interior, do not  
get water or cleaning fluids on the unit.  
2. The CD player will not operate properly in  
extreme hot/cold or under damp  
conditions. In case of such conditions, wait  
until the vehicle interior reaches a normal  
temperature or any condensation on the  
disc player lens has evaporated before  
using the player.  
procedures. We recommend using the latest  
versions of ROXIOTM or NEROTM burning  
software.  
5. Do not stick paper, tape or CD labels on  
disc surfaces, as internal damage may  
occur.  
3. Never insert anything other than round 5”  
CDs into the player. Attempting to insert  
CDs of other sizes (even with an adaptor)  
will cause damage not covered by the  
warranty.  
In addition, this unit will only recognize the  
CDDA (Compact Disc Digital Audio) format  
"recorded / burned" onto a CD-R/RW. This unit  
does not support .MP3, .WMA, .WAV, .OGG  
or other formats. The CDDA format is the  
standard format of an "original store bought"  
CD. When recording / burning a CD-R/RW  
make sure the CDDA format is selected.  
4. Always remove the CD when the player is  
not is use.  
5. The unit is designed with a vibration  
dampening CD mechanism to minimize  
interruption of disc play due to normal  
vibration in a moving vehicle. However,  
occasional sound skips may occur when  
driving on very rough roads. This will not  
scratch or damage the disc, and normal  
play will resume when the rough  
CD Care and Handling  
Dirt, dust, scratches and warpage can cause  
skips in the playback and deterioration of sound  
quality. Please follow these guidelines to take  
care of your compact discs.  
conditions cease.  
1. Carefully wipe fingerprints, dust and dirt  
from the disc’s playing surface with a soft  
15  
 
CD1211  
TROUBLESHOOTING  
Problem  
Cause  
Corrective Action  
Does not operate (display does not  
light)  
No power to yellow wire; no power to red wire  
Check connection with test light; check vehicle fuse with test  
light.  
Inline fuse blown  
Replace fuse.  
No power to unit  
Inline fuse blown  
Check/replace fuse.  
Not all speakers operate  
Incorrect splices or connections  
Check all splices and connections.  
Speaker wires shorting to chassis ground or to Check splices; insulate all bare wires.  
each other  
Blows fuses  
Power wire shorting to ground  
Speaker wires shorting to ground  
Incorrect fuse or fuse too small  
Make sure wire is not pinched.  
Make sure wire is not pinched.  
Install fuse of correct rating.  
CD skips too much  
Receiver mount is not solid or backstrap is not  
secure  
Check mounting and backstrap; tighten if needed.  
16  
 
CD1211  
SPECIFICATIONS  
AM Tuner  
CEA Power Ratings  
Tuning range: 530kHz-1710kHz  
Sensitivity @ 20dB signal to noise: 30uV  
Frequency response: 50Hz-2kHz., -3dB  
Auxiliary Input  
Input sensitivity: 400mV RMS for 1 watt RMS  
into 4-ohms  
Frequency response: 20Hz to 20kHz, -3dB  
Input impedance: 10 k-ohms  
General  
Power supply: 11-16 VDC, negative ground  
Power Antenna (Blue): 500mAmp Max, current  
limited protection.  
Operating Temp: -10C~60C  
Fuses: 15 amp fast blow ATO  
DIN chassis dimensions: 2"H x 7"W x 7"D  
(51mm x 178mm x 178mm)  
Power output: 13 watts RMS X 4 channels into  
4-ohms @ < 1% THD+N  
Signal to noise ratio: 70dBA below reference.  
(Reference: 1 watt, 4-ohms)  
Frequency response: 20Hz to 20kHz (-3dB),  
Auxiliary input used as source reference  
Reference supply voltage: 14.4VDC  
Specifications subject to change without  
notice.  
CD Player  
Signal-to-noise ratio: >90dBA  
Frequency response: 20Hz-20kHz, -3dB  
Channel separation: >55dB @ 1kHz  
D/A converter: 1 Bit/CH  
FM Tuner  
Tuning range: 87.5MHz-107.9MHz  
Mono sensitivity: 12dBf  
50dB quieting sensitivity (stereo): 16dBf  
Stereo separation @ 1kHz: >35dB  
Frequency response: 30Hz-14kHz. +3dB  
17  
 
Limited Warranty  
DO NOT RETURN THIS PRODUCT TO THE STORE  
CD or Multimedia Radios/Headunits  
Audiovox Electronics Corporation (“the Company”) is committed to  
quality and customer service, and are pleased to offer you this  
Warranty. Please read it thoroughly and contact the Company at 1-800-  
323-4815 with any questions.  
Limitations  
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY  
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND,  
IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE  
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.  
Who is covered?  
The Company extends this warranty to the original retail purchaser of products  
purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or  
Canada. This warranty is not transferable or assignable. Proof of purchase is  
required in the form of an original sales receipt.  
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED  
WARRANTIES,  
INCLUDING  
ANY  
IMPLIED  
WARRANTY  
OF  
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS  
WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY  
HEREUNDER  
MERCHANTABILITY MUST BE BROUGHT WITHIN  
INCLUDING  
ANY  
IMPLIED  
WARRANTY  
OF  
What is covered?  
A
PERIOD OF 24  
The Company warrants that should this product or any part thereof, under normal  
use, be proven defective in material or workmanship within 90 days from the date  
of original purchase, such defect(s) will be repaired or replaced with a new or  
reconditioned product (at the Company's option) without charge for parts and  
repair labor.  
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE  
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL  
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS  
OR IMPLIED, WHATSOEVER. No person or representative is authorized to  
assume for the Company any liability other than expressed herein in connection  
with the sale of this product.  
What is not covered?  
This Warranty does not cover the following:  
Some states do not allow limitations on how long an implied warranty lasts or the  
exclusion or limitation of incidental or consequential damage so the above  
limitations or exclusions may not apply to you. This Warranty gives you specific  
legal rights and you may also have other rights which vary from state to state.  
Damage incurred during shipping or transporting the product to the  
Company or a service center  
Elimination of car static or motor noise  
Defects in cosmetic, decorative or non-operative structural parts  
Correction of antenna problems  
Costs incurred for installation, removal or reinstallation of the product  
Consequential damage to compact discs, USB devices, digital media  
cards, accessories or vehicle electrical systems  
Obtaining Warranty Service  
To obtain repair or replacement within the terms of this Warranty,  
call 1-800-323-4815 for the location of a warranty station serving  
your area.  
Damage caused by improper installation, mishandling, misuse, neglect,  
accident, blown fuse, battery leakage, theft or improper storage  
Products whose factory serial number/bar code label(s) or markings  
have been removed or defaced  
Damage resulting from moisture, humidity, excessive temperature,  
extreme environmental conditions or external natural causes  
You must prepay the initial shipping charges to the Company.  
The Company will pay the return shipping charges for all  
warranteed products returned to an address within the U.S.A.,  
Puerto Rico or Canada.  
Please package the product securely to avoid shipping damage.  
We recommend using a carrier that provides tracking service to  
prevent lost packages. Lost or damaged packages are not  
covered by this warranty.  
Please review the “Care and Maintenance” section of your Installation  
and Operation Manual for additional information regarding the proper  
use of your product.  
Provide a detailed description of the problem(s) for which you  
require service.  
 
 
Audiovox Electronics Corporation  
150 Marcus Boulevard  
Hauppauge, NY 11788  
1-800-323-4815  
©2007 Audiovox  
v.083107  
 

Indesit Freezer CA 55 XX UK User Manual
Indesit Oven FIE 56 KB GB User Manual
Insignia Home Theater System NS H4005 User Manual
John Lewis Washer Dryer JLWM 1203 User Manual
JVC Camcorder GR AX680 User Manual
JVC CD Player KS FX772R User Manual
JVC TV DVD Combo AV 20FD22 User Manual
Knoll Systems Stereo System MR64 User Manual
Kodak Printer KY0730482 User Manual
Korg Guitar A5 User Manual