KitchenAid Trash Compactor W10242569B User Manual

INTEGRATED COMPACTOR  
Use & Care Guide  
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at  
In Canada, for assistance, installation or service, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca  
Table of Contents............................................................................................................2  
W10242569B  
 
IMPORTANT SAFETY INSTRUCTIONS  
WARNING:When using an electrical appliance, basic precautions should always be followed, including the following:  
Read all instructions before using the compactor.  
Do not compact toxic or volatile flammable material such as  
oily rags and insect sprays. Do not compact lighted  
cigarettes, cigars, or other hot or burning items. Do not  
overload the compactor.  
Close supervision is necessary when used by or near  
children. Do not allow to be used as a toy, or to run  
unattended at any time. Lock Key Switch when not in use  
and store key out of reach of children.  
Do not take apart the compactor. Incorrect reassembly can  
cause electric shock when subsequently used.  
Do not touch moving parts.  
Handle a loaded trash bag with care. Sharp objects can  
pierce the bag and cause injury. Do not overload trash bag  
with heavy material such as glass.  
Do not operate with a damaged cord set, plug, motor, or  
after damage in any manner. Have the compactor  
examined, repaired or adjusted by an authorized  
serviceperson.  
This compactor is intended for household use only.  
Use only for intended use as described in this manual. Do  
not use other than manufacturer's recommended  
attachments.  
SAVE THESE INSTRUCTIONS  
INSTALLATION INSTRUCTIONS  
Installer: Leave Use and Care Guide with the homeowner.  
Homeowner: Keep Use and Care Guide for future reference and  
for local electrical inspector’s use, if required.  
Unpacking  
6. Place the 2 corner posts from the carton on the floor near the  
compactor.  
WARNING  
Excessive Weight Hazard  
7. Open the compactor drawer and remove any shipping  
materials or other items from the drawer.  
NOTE: Do not remove the compactor bag.  
Use two or more people to move and install compactor.  
Failure to do so can result in back or other injury.  
8. Grasp the handle and raise the front of drawer until it clears  
the drawer stops.  
9. Grasp sides of drawer and lift drawer out of compactor.  
10. Place the drawer on the 2 corner posts.  
IMPORTANT:  
Do not grasp console to move compactor.  
Begin in the room where the compactor will be located.  
1. Remove compactor from shipping carton.  
2. Remove all packaging materials such as tape and shipping  
pads.  
3. Use a mild detergent and warm water to remove waxy  
residue caused by shipping material.  
4. Dry thoroughly with a soft cloth. For more information, see  
“Cleaning.”  
11. Place the other 2 corner posts on the floor to the side of the  
5. Be sure the power cord is attached to the cord clip on the  
compactor.  
rear of the compactor.  
12. Grasp the sides of the compactor cabinet and put compactor  
on its side on top of the corner posts.  
A
A. Cord clip  
3
 
13. Remove the shipping base from the bottom of the compactor.  
Clearance Dimensions  
A
B
A. Leveling legs  
B. Shipping base  
Location Requirements  
A
Product Dimensions  
B
A. Leave 6" (15.2 cm) of clearance space to the right side of the  
compactor in order to remove the compactor bags.  
B. Leave 23" (58.4 cm) of clearance in front of the compactor in  
order to fully open or remove the compactor drawer.  
Electrical Requirements  
34¹⁄₈"  
(86.7 cm)  
WARNING  
24"  
(61 cm)  
15"  
(38.1 cm)  
Electrical Shock Hazard  
Plug into a grounded 3 prong outlet.  
Do not remove ground prong.  
Do not use an adapter.  
Cutout Dimensions  
Do not use an extension cord.  
Failure to follow these instructions can result in death,  
fire, or electrical shock.  
3" min.  
(7.6 cm)  
Recommended Grounding Method  
This compactor is for use on a single phase, 115-volt, 60 Hz, AC  
only, 15- or 20-amp fused and properly grounded circuit and is  
equipped with a grounding plug as shown below. It is  
recommended that a separate circuit serving only this appliance  
be provided.  
A
34¹⁄₄" min.  
(87 cm)  
24" min.  
(61 cm)  
18" min.  
(45.7 cm)  
This compactor must be grounded while in use to reduce the risk  
of electric shock. The compactor is equipped with a three-  
conductor cord and 3 prong grounding-type plug to fit the proper  
grounding-type receptacle. The green (or green and yellow)  
conductor in the cord is the grounding wire.  
15¹⁄₄" min.  
(38.7 cm)  
A. Grounded eletrical outlet must be a minimum of 3" (7.6 cm) away  
from surrounding cabinets or nearby walls as shown. It can be  
placed either to the left or the right side of the compactor.  
NOTE: Do not connect the green (or green and yellow) wire to a  
live terminal.  
4
 
Undercounter Installation  
NOTE: Proper installation is your responsibility. Make sure you  
2. Use pliers to lower the leveling legs away from the cabinet.  
Adjust the legs so there will be a ¹⁄₈" (3 mm) to ¹ꢀ₄" (6.4 mm)  
space between the top of the compactor and the top of the  
cabinet opening. Stand the compactor upright.  
have everything necessary for correct installation. It is the  
personal responsibility and obligation of the customer to contact  
a qualified installer to assure that electrical installation meets all  
National and Local codes and ordinances.  
3. For model with cabinet, remove the plastic plugs from the  
compactor cabinet top.  
Tools Needed  
4. Move the compactor close to its final position.  
5. Plug into a grounded 3 prong outlet.  
Gather the required tools and parts before starting installation.  
Level  
Tape measure  
Pliers  
Phillips screwdriver  
Flat-blade screwdriver  
⁵⁄₁₆" box-end wrench  
Utility knife  
6. Determine if you want the compactor frame or drawer front  
flush with the cabinet front.  
Using the two #8-18 x ⁵ꢀ₁₆" screws, install the retaining  
brackets to cabinet top as needed:  
Scissors  
IMPORTANT:  
If the compactor frame is to be flush with the cabinet  
front, place retaining bracket screws through “1.”  
Do not grasp control panel to move compactor.  
If the compactor drawer front is to be flush with the  
cabinet front, place retaining bracket screws through “3.”  
Slide compactor onto cardboard or hardboard before moving  
compactor across floor to avoid floor covering damage.  
If the compactor is to be midway between “1” and “3,”  
place the retaining bracket screws through “2.”  
Do not allow the rear frame of the compactor to touch the  
floor covering when lifting or moving compactor.  
A
B
Undercounter Installation  
NOTE: Installation hardware is not provided with full cabinet  
models.  
3
2
1. Measure the height of your cabinet opening. The top of the  
compactor should be at least ¹ꢀ₈" (3 mm) from the top of the  
cabinet opening.  
1
The rear wheels are preset for a cabinet opening height of  
34¹⁄₄" (87 cm) (Position 1).  
To adjust for other cabinet opening heights:  
A. Countertop  
B. Retaining bracket  
Loosen self-tapping screw just enough to clear stud from  
hole in position 1.  
Move the rear wheel and stud to position 2 or 3 as  
needed for your cabinet opening measurement:  
7. Slowly lift the front slightly and roll compactor into the cabinet  
opening.  
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)  
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)  
Using the two #8-18 x ¹ꢀ₂" screws, fasten the retaining  
brackets to the countertop with the mounting screws.  
NOTE: To level the unit in position 3, you may need to  
If brackets cannot be attached to the underside of  
countertop, attach mounting clips to brackets. Fasten  
compactor to cabinet front with mounting screws through  
mounting clips.  
add shims under the leveling legs.  
Tighten screw.  
Repeat for other rear wheel.  
Countertop Mounting  
B
A
1
2
3
C
B
C
A
A. Countertop  
B. Retaining bracket  
C. Mounting screw  
D
A. Wheel bracket assembly  
B. Cabinet  
C. Locating stud  
D. Self-tapping screw (pivot)  
5
 
Cabinet-face Mounting  
Installation  
1. Remove the 2 rubber bumpers from the lower corners of the  
inside drawer front. Set aside the bumpers and discard the  
screws.  
C
D
A
2. Align the bottom of the custom panel with the bottom of the  
exterior drawer front and rest the panel on the rest tab.  
NOTE: The bottom of the custom panel should not extend  
below the bottom rest tab at the lower center of the exterior  
drawer front.  
B
3. Secure the custom panel to the exterior drawer front by using  
four #8 x 1" wood screws from the inside drawer front.  
Install the top 2 wood screws as shown.  
Use the bottom 2 wood screws to also re-install the  
2 rubber bumpers on each side of the lower inside drawer  
while attaching to the custom panel.  
A. Mounting clip  
B. Cabinet  
C. Retaining bracket  
D. Mounting screw  
8. Grasp sides of the compactor drawer and place the bottom  
4. Attach a 15" x ¹⁄₂" (38.1 cm x 13 mm) quarter-round filler  
along the top inside edge of the drawer front using glue or  
screws.  
of the drawer into the tracks.  
9. Lift at the handle so the drawer will go over the drawer stops.  
10. Close the drawer.  
11. Check that the drawer opens freely. If the toe plate rubs  
against the floor, see “Adjusting the Toe Plate” for further  
instructions.  
A
Adjusting the Toe Plate  
D
B
C
If the toe plate rubs the floor covering, the toe plate clearance  
may be changed as follows:  
1. Mark on each side of the toe plate the amount of toe plate  
D
that rubs the floor covering.  
2. Remove the drawer from the unit. See Step 3 in the  
“Unpacking” section.  
3. Use a ruler and a pencil or chalk to draw a line between the  
marks on each side of toe plate.  
E
4. Use scissors or utility knife to cut toe plate along line.  
5. Replace the drawer. If the toe plate still rubs the floor  
covering, repeat steps 1 to 4.  
Installing a Custom Panel  
Dimensions  
A. Custom panel  
B. 15" x ¹⁄₂" (38.1 cm x 13 mm)  
quarter-round filler  
D. #8 x 1" wood screws  
placement  
E. Rubber bumper (one on  
each side)  
Use these dimension drawings to create a custom panel for use  
without a trim kit. The panel should be a minimum of ¹⁄₂" (13 mm)  
thick.  
C. Drawer front  
29 ³⁄₈"  
(74.6 cm)  
15"  
(
)
38.1 cm  
6
 
COMPACTOR USE  
2. Place trash in compactor.  
Wrap or cover wet or messy trash.  
How Your Compactor Works  
The compacting ram is the part of the compactor which  
compresses the trash. The compacting ram does not go to the  
bottom of the drawer. You will not see compacting of trash the  
first few times you load the compactor.  
Do not compact items that may develop offensive odors  
such as raw meat, fish, grapefruit rinds, disposable  
diapers, or personal hygiene items.  
Load bottles or cans on their sides in the center of the  
drawer. Do not load bottles in an upright position.  
NOTE: The compactor drawer should be more than ¹⁄₂ full before  
the compactor can begin to compress the load.  
You may hear a noise when glass breaks. Strong glass bottles  
may not break at all. The trash in a full compactor bag will be  
about ¹⁄₄ the size of its original bulk.  
3. Close the drawer.  
WHISPER QUIET® Plus System  
The WHISPER QUIET® Plus system helps to maintain a quiet  
home environment during compactor operation.  
Load bulky trash, bottles, and cans in the center of the drawer.  
Bottles or cans not placed in the center may become caught  
between the ram and the drawer. The Drawer Monitor Switch  
then senses a “misload” and causes the ram to return to the “up”  
position without compacting.  
NOTE: The contents of the trash may affect the noise level of  
your compactor. See “Compactor Use.”  
Starting the Compactor  
1. Open the container. Load trash.  
2. Leave the Key-Knob in the ON position.  
3. Set the Solid Cycle switch to OFF.  
4. Close the container.  
5. Press the foot-actuated START pedal to begin cycle.  
Using Solid (Locked) Cycle  
The Solid (Locked) Cycle extends the use of the bag by putting  
constant pressure on the trash to keep it from springing back.  
Regular use of solid cycle can increase bag capacity up to  
25 percent.  
Loading  
IMPORTANT: Do not push items down into compactor with  
During Solid Cycle, the ram will stay in the down position for  
extra compacting. The drawer is locked and cannot be opened  
when the ram is down.  
hands or feet.  
NOTE: You will not see compacting of trash the first few times  
you load the compactor. The compactor drawer should be about  
¹⁄₂ full before the compactor can begin to compress the load.  
For best results, use the Solid Cycle for at least 30 minutes at a  
time.  
1. Open the drawer. Lift and pull the handle or press the toe bar  
1. Open the container. Load trash.  
2. Set the Solid Cycle switch to ON.  
to open the drawer.  
NOTE: Pressing the toe bar opens the container only 3" to 6"  
(7.6 cm to 15.2 cm), depending on the load.  
3. Close the container.  
4. Press the foot-actuated START pedal to begin cycle.  
5. The container remains LOCKED untill you RESET by pressing  
the foot-actuated START pedal.  
7
 
Using the Air Filter or Freshener  
Installing a New Bag  
1. Set the Air Filter switch to ON. The fan creates air movement  
Do not use any kind of bag other than those designed especially  
for use in your compactor. Order replacement compactor bags  
through your local dealer or by calling the toll-free number on the  
cover or in the “Assistance or Service” section.  
in the compactor for odor removal.  
NOTE: The charcoal Air Flter works only when the Key-Knob  
is in the ON position.  
IMPORTANT:  
Before installing a new bag, be sure:  
IMPORTANT: The air freshener will work with or without the  
fan.  
The drawer side is securely locked.  
2. Set the Air Filter switch to OFF to turn off the fan.  
The container is clean and free of debris.  
1. Place folded bag into the drawer. Open bag and pull top  
edges over the drawer top.  
Removing a Filled Bag  
When the trash is compacted to the top of the drawer, remove  
the bag. If the bag is too heavy, compact less trash before  
emptying it in the future.  
2. Lock bag in place by pulling the 4 prepunched holes over the  
bag retainer buttons. Holes will expand over the buttons  
without damaging the bag.  
IMPORTANT: Do not push items down into compactor with  
hands or feet.  
3. Press inside of bag against the drawer bottom, sides and  
1. Pull the drawer completely open.  
corners for a smooth fit.  
2. Remove top of bag from bag retainer buttons. Pull up all  
4 bag cuffs. Close bag with twist tie provided.  
3. Push Side-Lock Latch down and tilt drawer side open.  
4. Lift out bag.  
8
 
COMPACTOR CARE  
Your new compactor is designed to give you many years of  
Cleaning Inside the Drawer  
dependable service. However, there are a few things you are  
expected to do in order to properly maintain your compactor.  
This section will tell you how to clean and care for your  
compactor.  
NOTE: You may want to wear gloves since there may be bits of  
glass in the drawer.  
1. Remove the bag. See “Removing a Filled Bag.”  
2. Press down on the lever-action lock (or Side-Lock latch).  
Changing the Air Filter or Freshener  
It is recommended that you use either the charcoal air filter or the  
air freshener in the filter compartment. The solid air freshener  
system is an alternative to the air filter and is designed to control  
odors that might develop in the trash.  
To order the correct replacement charcoal filters or air fresheners,  
call the toll-free number listed on the cover or in the “Assistance  
or Service” section.  
1. Insert fingertips in the air filter cover and pull until the side  
3. Hold the lever-action lock down and tilt the side of the drawer  
tabs release. Then, lift the cover to release the bottom tabs.  
out until the lock clears the drawer front.  
NOTE: If desired, the drawer side can be removed by tilting it  
up, then lifting it out.  
2. Remove the air filter by pulling the top edge of the filter. The  
filter should pull out easily. Throw away used filter.  
OR  
Remove the air freshener by simply lifting out of the filter  
compartment. Throw away used freshener.  
4. Wash the interior of the drawer with a clean sponge or soft  
cloth and a mild detergent in warm water. Rinse and dry  
thoroughly with a soft cloth.  
5. If the drawer side was removed, slide it back into the tilted  
position.  
6. Press the lever-action lock (or Side-Lock Latch) down while  
pushing the drawer side to the upright position.  
7. Latch the drawer side by pushing up the lever-action lock (or  
Side-Lock Latch).  
3. To replace air filter, push the replacement filter into place.  
OR  
Cleaning Inside the Cabinet  
To replace the air freshener, place the replacement in the filter  
compartment.  
NOTE: You may want to wear gloves since there may be bits of  
glass in the cabinet.  
4. Insert the bottom tabs of the air filter cover and push in until  
1. Pull the drawer out until it stops.  
the side tabs snap into place.  
NOTE: Look to see how the drawer rollers move in the tracks.  
It will be easier to replace the drawer after you have finished  
cleaning.  
Cleaning  
Before cleaning the compactor, turn the Key-Knob (or Key-  
Switch) to the OFF & LOCK position and remove it.  
NOTE: Any services other than those outlined in this section  
should be performed by a designated service representative.  
Cleaning Exterior Surfaces  
1. Wash exterior surfaces (including stainless steel) with a clean  
sponge or soft cloth and a mild detergent in warm water. Do  
not use abrasive or harsh cleaners. Rinse and dry thoroughly  
with a soft cloth.  
2. Lift the front of the drawer to clear the stops.  
2. Wipe up spills right away. Some foods can damage the finish  
if left on the compactor surface.  
9
 
3. Grasp the drawer on the sides and pull it out the rest of the  
Cleaning the Ram  
way. Set the drawer down gently.  
NOTE: You may want to wear gloves since there may be bits of  
glass on the ram cover.  
1. Wipe glass particles off of the ram cover with a cloth or paper  
towels.  
2. Remove foods with a clean sponge or soft cloth and a mild  
detergent in warm water. Rinse and dry thoroughly with a soft  
cloth.  
4. Vacuum the inside of the cabinet. Liquid spills or wet trash  
should be cleaned up by hand, or by using a vacuum cleaner  
designed to pick up liquids.  
Cleaning Before a Vacation  
5. Wash the inside of the cabinet with a clean sponge or soft  
cloth and a mild detergent in warm water. Rinse and dry  
thoroughly with a soft cloth.  
If you will be away for more than a couple of days, remove the  
compactor bag. Remove the Key-Knob (or Key-Switch) and store  
it out of children’s reach.  
6. To replace the drawer, grasp it by the sides and insert the  
rollers onto the tracks.  
7. Lift the front of the drawer and push it in fully past the stops.  
TROUBLESHOOTING  
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.  
Trash is not compacting  
The drawer won’t open  
Is the drawer less than half-full? Drawer must be more than  
half full before trash is compacted.  
Is the ram all the way up? Drawer will open only when ram is  
fully raised.  
To raise the ram on models with a Key-Knob (or Key-  
Switch): Turn the Key-Knob (Key-Switch) to START and  
release. See “Starting the Compactor.”  
Your compactor won’t operate  
Is the power supply cord unplugged? Plug into a grounded  
3 prong outlet.  
To raise the ram on models with push button controls:  
Press OFF, and then press ON. See “Starting the Compactor.”  
Has a household fuse blown, or has a circuit breaker  
tripped? Replace the fuse or reset the circuit breaker. If the  
problem continues, call an electrician.  
Is the Solid Cycle engaged? Drawer remains LOCKED until  
you reset by lifting the foot pedal up.  
Is the drawer completely closed? Close the drawer firmly  
and start the compactor again.  
There is not enough compaction or force  
Is the Key-Knob turned all the way to START? Turn the  
Key-Knob (Key-Switch) fully to START and release (on some  
models). See “Starting the Compactor.”  
Do you use the compacting cycle frequently enough?  
Compacting works best when only a few items are loaded.  
Bottles don’t break  
Did you press ON before pressing START? Press ON  
before pressing START (on some models). See “Starting the  
Compactor.”  
How often do you notice this? Bottles will not break every  
time. The thickness of the bottle’s glass and the content of  
the trash load below it may keep the bottle from breaking.  
10  
 
ASSISTANCE OR SERVICE  
Before calling for assistance or service, please check  
Troubleshooting.” It may save you the cost of a service call. If  
you still need help, follow the instructions below.  
If you need replacement parts  
If you need to order replacement parts, we recommend that you  
use only factory specified parts. These factory specified parts will  
fit right and work right because they are made with the same  
precision used to build every new KITCHENAID® appliance.  
When calling, please know the purchase date and the complete  
model and serial number of your appliance. This information will  
help us to better respond to your request.  
To locate factory specified parts in your area, call us or your  
nearest KitchenAid designated service center.  
In the U.S.A.  
Call the KitchenAid Customer eXperience Center toll free:  
To locate the KitchenAid designated service company in your  
area, you can also look in your telephone directory Yellow  
Pages.  
1-800-422-1230 or visit our website at www.kitchenaid.com.  
Our Consultants Provide Assistance With:  
Features and specifications on our full line of appliances.  
For Further Assistance  
If you need further assistance, you can write to KitchenAid with  
any questions or concerns at:  
Installation information.  
Use and maintenance procedures.  
Accessory and repair parts sales.  
KitchenAid Brand Home Appliances  
Customer eXperience Center  
553 Benson Road  
Specialized customer assistance (Spanish speaking, hearing  
impaired, limited vision, etc.).  
Benton Harbor, MI 49022-2692  
Referrals to local dealers, repair parts distributors and service  
companies. KitchenAid designated service technicians are  
trained to fulfill the product warranty and provide after-  
warranty service, anywhere in the United States.  
Please include a daytime phone number in your correspondence.  
In Canada  
Call the KitchenAid Canada Customer eXperience Centre toll  
For Further Assistance  
free: 1-800-807-6777 or visit our website at www.kitchenaid.ca.  
If you need further assistance, you can write to KitchenAid  
Canada with any questions or concerns at:  
Our Consultants Provide Assistance With:  
Features and specifications on our full line of appliances.  
Customer eXperience Centre  
KitchenAid Canada  
200 - 6750 Century Ave.  
Mississauga, Ontario L5N 0B7  
Use and maintenance procedures.  
Accessory and repair parts sales.  
Referrals to local dealers, repair parts distributors and service  
companies. KitchenAid Canada designated service  
technicians are trained to fulfill the product warranty and  
provide after-warranty service, anywhere in Canada.  
Please include a daytime phone number in your correspondence.  
Accessories  
To ensure the proper functioning of your compactor, use  
KITCHENAID® replacement parts only. To order replacement  
parts or accessories, call 1-800-462-3819 and ask for the  
appropriate part number listed below or contact your authorized  
KitchenAid dealer. In Canada, call 1-800-807-6777.  
Color Panel Kits and Handles  
See section “Installing a Custom Panel” for custom panel  
dimensions.  
Color Panel with Handles:  
Replacement Parts  
Cobalt Blue—Part Number 4396299  
Empire Red—Part Number 4396300  
Majestic Yellow—Part Number 4396301  
Black—Part Number 4396296  
White—Part Number 4396297  
Biscuit—Part Number 4396298  
Handles:  
Replacement Bags: Call for Part Number.  
Charcoal Air Filters: Part Number 4151750  
Air Fresheners (scent):  
Fresh Green Apple—Part Number 9872166GA  
Lavender—Part Number 9872166L  
Lemon Grove—Part Number 9872166LG  
Brushed Stainless Steel—Part Number 9871564  
White—Part Number 9871564W  
Black—Part Number 9871564B  
Biscuit—Part Number 9871564T  
11  
 
KITCHENAID® COMPACTOR WARRANTY  
ONE YEAR LIMITED WARRANTY  
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or  
furnished with the product, KitchenAid or KitchenAid Canada (hereafter “KitchenAid”) will pay for factory specified parts and repair  
labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.  
30 DAY LIMITED WARRANTY ON THE CHARCOAL FILTER AND AIR FRESHENER  
For thirty days from the date of purchase, when the compactor is installed, operated and maintained according to instructions attached  
to or furnished with the product, KitchenAid will provide a replacement filter or air freshener if the original filter or air freshener fails due  
to defects in materials or workmanship.  
ITEMS KITCHENAID WILL NOT PAY FOR  
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair  
house fuses or to correct house wiring or plumbing.  
2. Service calls to repair or replace appliance light bulbs or water filters. Those consumable parts are excluded from warranty  
coverage.  
3. Repairs when your major appliance is used for other than normal, single-family household use.  
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in  
accordance with electrical or plumbing codes, or use of products not approved by KitchenAid.  
5. Replacement parts or repair labor costs for units operated outside the United States or Canada.  
6. Pickup and delivery. This major appliance is designed to be repaired in the home.  
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.  
8. Expenses for travel and transportation for product service in remote locations.  
9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with  
published installation instructions.  
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES  
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED  
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,  
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR  
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION  
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF  
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES  
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE  
TO PROVINCE.  
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if  
another warranty applies.  
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help  
can be found by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,  
call 1-800-807-6777.  
9/05  
Keep this book and your sales slip together for future  
reference. You must provide proof of purchase or installation  
date for in-warranty service.  
Dealer name____________________________________________________  
Address________________________________________________________  
Phone number__________________________________________________  
Model number __________________________________________________  
Serial number __________________________________________________  
Purchase date __________________________________________________  
Write down the following information about your major appliance  
to better help you obtain assistance or service if you ever need it.  
You will need to know your complete model number and serial  
number. You can find this information on the model and serial  
number label located on the product.  
11/13  
Printed in U.S.A.  
®/™ ©2013 KitchenAid. Used under license in Canada. All rights reserved.  
W10242569B  
 

Indesit Clothes Dryer ISL60V User Manual
Indesit Washer PWC 8148 W User Manual
Ingersoll Rand Water Pump 6544X X User Manual
JBL Speaker IBT User Manual
Jenn Air Oven JMW9527DAB User Manual
JVC Car Stereo System Model KD ABT22J User Manual
Jwin Digital Photo Frame JP 121 User Manual
Kenwood Car Stereo System TM 732E User Manual
Kingston Technology Network Router 480 15FUM 001A00 User Manual
Kompernass Sander PSS 260 User Manual