Infinity Speaker C205 User Manual

INFINITY CLASSIA SPEAKERS  
OWNER S GUIDE  
C205  
C336  
CC225  
 
WALL-MOUNTING THE CC225  
WALL-MOUNTING THE C205  
The CC225 is designed to be mounted directly to a wall.The bracket has  
four holes on the back, and will require (4) 1-1/2,"#8 wood screws with  
a .33" (8.4mm) screwhead fastened to wall studs. If wall studs are unavail-  
able, install anchors appropriate for a 1-1/2,"#8 screw.  
The C205 is designed to be mounted directly to a wall. Each speaker has  
two keyholes on the back, and will require (2) 1-1/2,"#8 wood screws  
with a .33" (8.4mm) screwhead fastened to a wall stud. If a wall stud is  
unavailable, install an anchor appropriate for a 1-1/2,"#8 screw.  
NOTE: The customer is responsible for the correct selection and use  
of mounting hardware (available through hardware stores) that will  
ensure the proper and safe wall-mounting of the speakers.  
NOTE: The customer is responsible for the correct selection and use of  
mounting hardware (available through hardware stores) that will ensure  
the proper and safe wall-mounting of the speakers.  
Step 1.  
Attach the wall bracket to the wall at the desired location.  
Keyhole mounts  
Step 2.  
Securely fasten the two cleats to the rear of the speaker,  
using two included 1/4"-20 panhead screws per cleat.  
Attach rubber bumper  
Figure 4.  
Step 1.  
Mark the positions on the wall where you would like to place the  
mounting screws.  
Step 3.  
Step 2.  
Carefully slide the cleats on the rear of the speakers over the tabs  
of the wall bracket.  
Fasten two 1-1/2,"#8 wood screws to the wall using the markings placed  
in Step 1 as your guide. Leave an 11/16" space between the wall and  
screwhead. If a wall stud is not available, use an appropriate anchor.  
Step 3.  
Place the speaker on the wall by aligning the keyholes on the back of  
the speaker to the screwheads on the wall. Once positioned properly,  
the speaker should slide down slightly and become secure.  
INSTALLING SPIKED FEET  
C336  
Four metal spikes are supplied for use when using the outboard feet and  
the speaker is to be placed on a carpeted surface to decouple the speaker  
from the floor and prevent unwanted damping.To insert the spikes, gently  
lay the speaker on its back (not its front or side) on a soft, nonabrasive  
surface, unscrew the four rubber-tipped feet and store in a safe place.  
Each spike then screws into the threaded insert. Make sure all four spikes  
are screwed in completely for stability.  
Top view  
NEVER drag the speaker to move it, as this will damage the spikes, the feet, the  
wood cabinet itself, and/or the floor. Always lift the speaker and carry it to its  
new location.  
INFINITY CLASSIA 3  
 
WIRING THE SYSTEM  
BI-WIRING  
C336  
IMPORTANT: Make sure all equipment is turned off before making any  
connections.  
The outer connection panel and internal dividing network of the C336 is  
designed so that separate sets of speaker cables can be attached to the low-  
frequency transducer and midrange/high-frequency transducer portions of this  
dividing network.This is called bi-wiring. Bi-wiring can provide several sonic  
advantages and considerably more flexibility in power amplifier selection.  
For speaker connections, use a minimum #16-gauge speaker wire with  
polarity coding.The side of the wire with a ridge or other coding is  
usually considered positive polarity (i.e., +).  
NOTE: If desired, consult your local Infinity dealer about speaker wire and  
connection options.  
The speakers have coded terminals that accept a variety of wire connec-  
tors.The most common connection is shown in Figure 5.  
To ensure proper polarity, connect each + terminal on the back of the  
amplifier or receiver to the respective + (red) terminal on each speaker,  
as shown in Figure 6. Connect the (black) terminals in a similar way.  
See the owner’s guides that were included with your amplifier, receiver  
and television to confirm connection procedures.  
IMPORTANT: Do not reverse polarities (i.e., + to , or to +) when  
making connections. Doing so will cause poor imaging and diminished  
bass response.  
Figure 7.  
Single-Stereo Amplifier  
Figure 5.This example shows how to connect bare wires to the terminals.  
Figure 8.  
Dual-Stereo Amplifier  
Figure 9.  
Figure 6.Wiring diagram shows polarity connections for one  
channel of a stereo or home theater system.  
4 INFINITY CLASSIA  
 
FINAL ADJUSTMENTS  
Check the speakers for playback, first by setting the system volume control  
to a minimum level, and then by applying power to your audio system. Play  
a favorite music or video segment and increase the system volume control  
to a comfortable level.  
NOTE: You should hear balanced audio reproduction across the entire  
frequency spectrum. If not, check all wiring connections or consult  
the authorized Infinity dealer from whom you purchased the system  
for more help.  
The amount of bass you hear and the stereo-image quality will be affected  
by a number of different factors, including the room’s size and shape,  
the construction materials used to build the room, the listener’s position  
relative to the speakers, and the position of the speakers in the room.  
Listen to a variety of music selections and note the bass level. If there is  
too much bass, move the speakers away from nearby walls. Conversely, if  
you place the speakers closer to the walls, there will be more bass output.  
Nearby reflecting surfaces can adversely affect stereo-imaging quality. If  
this happens, try angling the speakers slightly inward toward the listening  
position until the optimal effect is achieved.  
CARE OF YOUR SPEAKER SYSTEM  
Each Infinity Classia cabinet has a finish that does not require any routine  
maintenance.When needed, use a soft cloth to remove any fingerprints or  
dust. Clean the grille by gentle vacuuming.  
NOTE: Do not use any cleaning products or polishes on the cabinet  
or grille.  
In the event that your Infinity speaker needs service, contact your Infinity  
the nearest service center.  
INFINITY CLASSIA 5  
 
SPECIFICATIONS  
C205  
C336  
CC225  
Frequency Ranges:  
60Hz – 30kHz (–3dB)  
55Hz – 40kHz (–6dB)  
40Hz – 30kHz (–3dB)  
35Hz – 40kHz (–6dB)  
55Hz – 30kHz (–3dB)  
50Hz – 40kHz (–6dB)  
Recommended  
Amplifier Power Range:  
10 – 125 Watts  
10 – 250 Watts  
91dB  
10 – 150 Watts  
90dB  
@
Sensitivity (2.83V 1 meter): 88dB  
Nominal Impedance:  
8 Ohms  
2.0kHz; 24dB/octave  
8 Ohms  
8 Ohms  
Crossover Frequencies:  
Low-Frequency Driver(s):  
500Hz, 2.8kHz; 24dB/octave  
2.0kHz; 24dB/octave  
®
®
®
5-1/4" (133mm) CMMD,  
magnetically shielded  
Triple 6-1/2" (165mm) CMMD,  
magnetically shielded  
Dual 5-1/4" (133mm) CMMD,  
magnetically shielded  
Mid-Frequency Driver:  
High-Frequency Driver:  
Dimensions (H x W x D):  
Weight:  
N/A  
4" (100mm) CMMD,  
magnetically shielded  
N/A  
1" (25mm) CMMD,  
magnetically shielded  
1" (25mm) CMMD,  
magnetically shielded  
1" (25mm) CMMD,  
magnetically shielded  
15-1/8" x 7-1/2" x 9-1/4"  
(384mm x 190mm x 235mm)  
48-3/4" x 8-1/2" x 10-1/2"  
(1238mm x 216mm x 267mm)  
6-7/8" x 31-3/4" x 5"  
(175mm x 806mm x 127mm)  
10.8 lb (4.9kg)  
56.1 lb (25.4kg)  
16 lb (7.3kg)  
Features, specifications and appearance are subject to change without notice.  
Declaration of Conformity  
We, Harman Consumer Group, Inc.  
2, route de Tours  
72500 Château du Loir  
France  
declare in own responsibility that the products described  
in this owners manual are in compliance with technical  
standards:  
EN 61000-6-3:2001  
EN 61000-6-1:2001  
Laurent Rault  
Harman Consumer Group, Inc.  
Château du Loir, France 12/07  
6 INFINITY CLASSIA  
 
NOTES  
INFINITY CLASSIA 7  
 
© 2007 Harman International Industries, Incorporated.All rights reserved.  
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4463 (USA only) www.infinitysystems.com  
Infinity and CMMD (patent nos. 6,327,372 and 6,404,897) are trademarks of Harman International Industries, Incorporated,  
registered in the United States and/or other countries. Infinity Classia is a trademark of Harman International Industries, Incorporated.  
Part No. BO-13333-01 12/07  
 

InFocus Car Video System INF7001A User Manual
Jackson Dishwasher JPX 300H User Manual
Jasco Computer Keyboard 98134 User Manual
Jensen Clock Radio JCR 300 User Manual
JVC CD Player KD ABT22 User Manual
JVC CRT Television AV 20D202 User Manual
Kenmore Microwave Oven 72180822 User Manual
Kenwood Stereo System DPX 302 User Manual
Kenwood Telephone M User Manual
KitchenAid Refrigerator KBLO36FMX01 User Manual